LGPXD-A自動高壓噴藥消毒器適用于機場、碼頭、船舶等大范圍區域快速消毒
沃特桑尼LGPXD-A自動高壓噴藥消毒器，可以自動連續按比例加藥（配比比例可按需要任意調節）；自動混藥，進水、混藥、配藥、噴灑消毒同時進行；原藥罐40L，儲藥罐500L，設備配藥精度誤差不大于1%。系統可24小時不間斷配藥，無需電源。自動泄壓裝置消毒停止后，降低管道壓力，恢復到常壓。藥箱采用316優質不銹鋼，容量500L，尺寸100*50*100cm，藥箱帶自動加熱系統，水溫可自動調節，設備在-40度正常運轉,藥箱帶自動液位計，藥液位置可視，工作異常報警，可自動顯示藥液升數。
維護注意事項：
若發現LGPXD-A自動高壓噴藥消毒器不出液，首先檢查噴嘴口或內流通道是否堵塞，溫度危害過熱對非高溫用處規劃的噴頭資料會有必定的危害影響。不正確的裝置違背軸心的墊圈，上緊或其它改動方位的問題均能發生不良影響，意外損害在裝置和清潔中，因為運用不正確的東西或許意外地對扇形噴嘴的噴頭形成損害，扇形噴嘴作為現代企業中常運用的一種設備之一，平常咱們在對他進行運用時，我們知道它的中心方位在哪里嗎，下面就一起來了解一下吧，以扇形噴嘴為例扇形噴嘴中心的部位是噴口，扇形噴嘴的噴口雖橢圓形的，噴口內腔潤滑刺。這樣才能確保扇形噴嘴在噴霧時，不會呈現不均勻、扇形噴嘴呈現傾斜等情況。通常來說，水滴會與粉塵粒子結合，粉塵顆粒不斷沉降，達到降塵和凈化空氣的效果，且該噴霧系統工程對噴霧裝置，自控，儀表。集成，專門用于固定管道布置除塵裝置，為生產運行服務產量，降低運行的成本，該系統具有伴熱系統，能設備在零下30℃環境下正常使用，高能微霧噴嘴；采用特種加工，WATERSUNNY負壓抽風式原理，通過數控機床加工而成，外殼采用304不銹鋼材質制造，具有沖擊力大，射程遠，噴霧顆粒細，磨損小，壓力損失小。抑塵效果好等特點。LGPXD-A自動高壓噴藥消毒器的流量可根據工況任意選擇，依據場地功能的不同，可采用不同大小的噴嘴，操作壓力達到30~130Kg，霧粒10~80微米。
Lgpxd-a automatic high-pressure spraying disinfector is suitable for rapid disinfection in large areas such as airports, docks and ships
Watersunny lgpxd-a automatic high-pressure spraying disinfector can automatically and continuously add medicine in proportion (the proportion can be adjusted as needed); automatic mixing, water inlet, medicine mixing, medicine dispensing and spraying disinfection are carried out at the same time; the raw medicine tank is 40L and the medicine storage tank is 500L, and the dispensing accuracy error of the equipment is not more than 1%. The system can dispense medicine 24 hours without power supply. After the disinfection of the automatic pressure relief device is stopped, the pipeline pressure is reduced and returned to normal pressure. The medicine box is made of 316 high quality stainless steel, with a capacity of 500L and a size of 100 * 50 * 100cm. The medicine box is equipped with an automatic heating system. The water temperature can be adjusted automatically. The equipment can operate normally at - 40 ℃. The medicine box is equipped with an automatic liquid level gauge. The position of the medicine liquid can be seen, and the abnormal working alarm can automatically display the number of medicine liquid liters.
Maintenance precautions:
If it is found that the lgpxd-a automatic high-pressure spraying sterilizer does not discharge liquid, first check whether the nozzle mouth or internal flow channel is blocked, and the overheating of temperature hazard will have a certain harmful effect on the non high temperature nozzle information. Incorrect device, washer against the axis, tightening or other problems of changing the orientation can have adverse effects. Accidental damage in the device and cleaning, because the use of incorrect things may cause accidental damage to the nozzle of fan nozzle. Fan nozzle is one of the commonly used equipment in modern enterprises. When we use it, we know its safety Where is the center? Let's take the fan nozzle as an example. The center of the fan nozzle is the nozzle. Although the nozzle of the fan nozzle is oval, the inner cavity of the nozzle is smooth. Only in this way can we ensure that the fan-shaped nozzles do not show uneven and fan shaped nozzle tilting when spraying. Generally speaking, droplets will be combined with dust particles, and dust particles will continuously settle down to achieve the effect of Dustfall and air purification, and the spray system works on the spray device, automatic control and instrumentation. The system has a heat tracing system, which can be used normally in the environment of minus 30 ℃ with high-energy micro fog nozzle; it adopts the principle of non-traditional machining and water sunny negative pressure ventilation, which is processed by numerical control machine tool, and the shell is made of 304 stainless steel with impact force Large, far range, fine spray particles, small wear and small pressure loss. The dust suppression effect is good. The flow rate of lgpxd-a automatic high-pressure spraying disinfector can be selected according to the working conditions. According to the different functions of the site, different sizes of nozzles can be used. The operating pressure can reach 30 ~ 130kg, and the fog particles can reach 10 ~ 80 μ M.